Hello everyone, It has been more than a month now that I have been having troubles with my internet. A cyclone hit and they recently restored it but still having downtime. I am pleased to say that I have been able to continuing my tests to make more stuff and because of that and the lack of internet for commissions I am running a little low on funds.
I will address everything I have missed first. [quote=“ThatchMac, post:768, topic:27337”]
your combined mask of time, have you been able to work on that? Just asking, take all the time you want on it. Finally, do you plan on adding a fit G2 mask clips to that Skull Kid mask? Because I’d love to put that onto a BIONICLE XD.
[/quote]
Sadly I have not. With the general consensus being you want the G1 Vahi fused on top of my G2 Vahi. I have not been able to find reference images to make an accurate model and do just that.
If anyone can take good images of the G1 Vahi and post them here I can get back on that and get it out. What I need to make it are a front image and a side image. Try and get it as straight and lined up as possible.
I am not sure that adding clips to Majora’s mask would work. Might turn out like that flat Vahi I posted a while ago.
Here is what i have done on that so far. I am very happy with how the bottom half looks but am not sure how to do the top half.Any advice is as all ways greatly appreciated.
Ah I did see this a little while ago. I love the design they have settled on and will be making the masks for those once I can get side views of the masks.
I very much like the idea of this board and have it tagged for new new message notifications now
Ixrollout and i have been missing each other on skype. We are trying to find a better way to keep in contact to get the final few tweaks done. After the titan scale is done i will move the changes to the villager scale.
Yes, yes I do. (View images above.)
No problem happy to help.
From what I have seen, yes it is a surprisingly good match.[quote=“Doomarak, post:775, topic:27337”]
would the references in the Art Book (bigger res available in the PDF) combined with the small preview from the leaked image of Umarak the Hunter be adequate to make a model of the Prototype Mask of Control, and if so how much would your commission price be to model it and put it on shapeways?
To those who ordered the MOUP in both Villager Scale and Titan Scale, how do they compare size-wise with the prototype mask on the original model? Which would is closer to the actual piece? Are either actually in scale with it to begin with, or are they just sized relative to The Journey to One?
[/quote]
My Commissions start at $40 (if you think this is too much keep in mind that i do spend about 6 hours minimum on a mask.) Also from what I can tell it would be cheaper to purchase a second Mask of control and use a file to cut the section out at the top and score some lines in.
The titan scale is accurate to the one used on the model in the promotional video. The villiger was made since the titan scale looked ridiculous on smaller sets
Sure what did you have in mind? 
[quote=“Azani, post:777, topic:27337, full:true”]
When could we expect word or some sort of update on the Axato mask for the Bionicle Legacy Project?
[/quote]
If my internet holds up. Tomorrow.[quote=“Altair, post:778, topic:27337”]
This mask is amazing
The strong and flexible polished is a great material, and if you look at it without paying much attention it’s almost like a completely smooth plastic.
is it possible to get a Mask of Ultimate Power in black strong and flexible polished? I think it would look better than standard strong and flexible.
[/quote]
That must be one done with the new sanding process they are using. It gives a much nicer finish.
Unfortunately not but the material they use does soak up paint nicely so that should work if you get a white one.
That looks beautiful. I am defs going to using those images on the shape ways page.
Right, now onto what I have been up to the past few weeks.
I am ready to make full scale Kanohi Mirus. I am just waiting for Eljay to publish the Interview I did with him then I will be posting a listing on Etsy that will give a discount on the actual price as well as two bonuses.
I am also ready to start printing these.
But due to lack of money at the moment can’t afford the material for such a large project.
I have been working on cleaning up a G2 Vahi that I made at home and practicing making intricate objects smoother while retaining the sharp corners. Hobby knives have become my best friend in this task.
I have Been working on making things I can sell if I get a booth at a pop culture convention.
Starting with a bunch of half scale iron man helmets. This is the only one I have printed at the moment. it took 13 hours and 45 minutes to print. I have a listing for that on Etsy here. going to use the money to by the material needed for the other full scale masks.
I am also thinking about making More Iron man stuff including gauntlets and gloves.
If anyone else can think of anything I could make or you think would be popular let me know.
Hopefully I can be more active on the site again now my internet is more stable.